ref: e81c54ba2ecc673a4d5f8aed0e9b52841fe07b0d
dir: /man/3/dbg/
.TH DBG 3 .SH NAME dbg \- remote kernel debugging .SH SYNOPSIS .B "bind -b '#b' /dev" .PP .B /dev/dbgctl .br .B /dev/dbglog .PP .BI "echo r >/dev/dbgctl" .SH DESCRIPTION .I Dbg allows a native kernel to be debugged remotely, by means of a simple protocol, typically run on a serial port (see .IR eia (3)). The .IR acid (10.1) debugger uses the protocol for instance; see its .B -R option. .PP .I Dbg uses the values of several global variables set by the kernel configuration file (see .IR conf (10.6)), all of which default values. The variables and default values are listed below: .IP .EX int dbgstart = 0; char *dbgdata = "#t/eia0"; char *dbgctl = "#t/eia0ctl"; char *dbgctlstart = "b19200"; char *dbgctlstop = "h"; char *dbgctlflush = "f"; .EE .PP Different values can be set by including similar declarations, with values as desired, in the .B code section of the configuration file. .I Dbg uses the values as follows: .TP \w'\f5dbgctlflushxx\fP'u .PD 0 .B dbgstart if non-zero, start the debugger protocol on the configured connection during driver initialisation (system startup); otherwise it must be started explicitly by the .B r control request (see below) .TP .B dbgdata data file for the debugging connection .TP .B dbgctl control file for the debugging connection .TP .B dbgctlstart control request to initialise link (eg, baud rate) .TP .B dbgctlstop control request to hang up link .TP .B dbgctlflush control request to write to flush input and output on link .PD .PP .I Dbg serves two files that control and monitor its operation. .PP .B Dbgctl accepts several textual commands; normally only .B r is needed: .TP .BI d " dbgdata" set the value of .B dbgdata to the value given as an argument .TP .BI c " dbgctl" .PD 0 .TP .BI i " dbgctlstart" .TP .BI h " dbgctlstop" .TP .BI f " dbgctlflush" set the value of the corresponding control variable to the value of the first argument .PD .TP .B r start running the debugger protocol (not needed if .B dbgstart was non-zero at boot) .TP .B s stop running the debugger protocol; stop and flush the link .PP When read, .B dbgctl yields a single line showing the status of the device .RB (` running ' or .RB ` stopped ') and the current values of the debugger control variables listed above. .PP .B Dbglog is a read-only text file containing lines representing debugger events, one per line. It is mainly useful for checking the operation of the device, or debugging new .IR acid (10.1) functions. .SS Debug protocol The protocol is subject to change. The host running the debugger and the target to be debugged exchange 10-byte messages containing a one byte message type and 9 bytes of data. Bytes unused by a given type are set to zero. Normally the host sends one of the T-messages below and receives the corresponding R-message, or .BR Rerr . (These are unrelated to the T-messages and R-messages of .IR intro (5).) Exceptionally, the target sends the first message, an .B Rerr to reset the protocol, and thus the debugger is notified if the target is rebooted during a debugging session and can reset its own state. Values, including addresses, are sometimes represented textually in hexadecimal, but are usually in binary as a single byte, or an array of 4 bytes, high-order byte first (big endian). .PP The term .I process here refers exclusively to those created directly or indirectly by .IR kproc (10.2), not to Limbo processes, which are not visible directly through the protocol (although it is possible to write .IR acid (10.1) functions that interact through .I dbg with the Inferno data structures representing the state of the Dis virtual machine). Many requests read or write the memory or state of the .IR "current process" set by the .B Tproc message (see below). Addresses are always 32 bits. An address below the size of .B Ureg (saved register state) for the target is interpreted as an offset within the saved state for the current process. Otherwise it refers to an address in kernel virtual memory. Currently in native Inferno all processes share the same address space. .PP The message type names used below are assigned values by declarations in .BR /include/rdbg.h . The following messages are currently implemented: .TP \w'Tstart'u .PD 0 .B Terr unused .TP .BI Rerr " reason\fR[9]\fR" The last message failed for the given .IR reason , a text string: .BR reset , the target or debug driver was restarted; .BR count , bad count; .BR unk , unknown command; .BR inval , invalid parameter; .BR pid , no such process; .BR unsup , unsupported action; .BR notstop , action requires process to be stopped first. .TP .BI Tmget " addr\fR[4]\fP n\fR[1]\fP" Request .I n bytes of memory from .IR addr ; .I n must be no greater than 9 .TP .BI Rmget " data\fR[9]\fP" Return .I data requested by .B Tmget .TP .BI Tmput " addr\fR[4]\fP n\fR[1]\fP data\fR[4]\fP" Write the first .I n bytes of .I data to memory at .IR addr , and flush the data and instruction caches for that region; .I n must be no greater than 4 .TP .BI Rmput Reply to a successful .B Tmput .TP .BI Tproc " pid\fR[4]\fP" Set the current process to the one with integer process ID .I pid for subsequent requests. .TP .BI Rproc " addr\fR[8]\fP" .I Addr is the address in hexadecimal text of the .B Proc structure for process .I pid in the corresponding .BR Tproc . .TP .BI Tstatus " pid\fR[4]\fP" Request the status of process .I pid leaving the current process ID unchanged. .TP .BI Rstatus " status\fR[9]\fP" Return the textual status of the process as a text string, currently one of: .BR Dead , .BR Moribund , .BR Ready , .BR Scheding , .BR Running , .BR Queueing , .BR Wakeme , .BR Broken , .BR Stopped , .BR Rendezvous , or if invalid, the state value as a hexadecimal number. .TP .BI Trnote " pid\fR[4]\fP" Retrieve the note (trap status) for the given .I pid .TP .BI Rrnote " status\fR[9]\fP" Provide the textual trap .I status for the requested process (currently always returns null status) .TP .BI Tstop " pid\fR[4]\fP" Tell the kernel to stop running process .I pid in debugging state .B Stopped when it next appears in the scheduler. .TP .BI Rstop Reply to successful .B Tstop .TP .BI Tstart Cancel a previous .BR Tstop ; if the process has already stopped, make it ready to run. .TP .BI Rstart Reply to successful .B Tstart .TP .BI Tcondbreak " val\fR[4]\fP op\fR[4]\fP" If .I op is .BR d , remove and delete the breakpoint with ID .IR val . All other operations help create a conditional breakpoint, providing a possibly empty list of operations representing a conditional expression in Reverse Polish is followed by a breakpoint request, each expression element represented by a single .B Tcondbreak message. .I Op is a single character representing an operation, with .I val (integer, address, process ID) as a parameter. The operator .B n should appear first; it assigns the breakpoint an ID number .I val (no greater than 255). Expression primaries are: .BI k " val," true if process .I val is at this breakpoint; .BI b " val," true if program counter is .IR val ; and .BI p " val," .I val as a 32-bit literal. Expression operators are: unary .B * (indirect, yielding 32-bit value); .B & (bit-wise AND); .B = (values equal); .B ! (values not equal); .B a (logical AND); .B o (logical OR). Although the expression is interpreted following Reverse Polish notation, when transmitted, the .B b operation is sent last (to mark the end of the sequence and create the breakpoint), but is moved to the start of the expression before evaluation. .TP .BI Rcondbreak Reply to successful .BR Tcondbreak . .TP .BI Tstartstop " pid\fR[4]\fP" If the process .I pid is not stopped, return .B Rerr .BR notstop . Otherwise, if the process is not stopped at a breakpoint, start it, and wait for it to reach a breakpoint that evaluates `true' .TP .BI Rstartstop " id\fR[1]\fP" Process has stopped at breakpoint with the given .I id .TP .BI Twaitstop Unimplemented. See .BR Tstartstop . .TP .BI Rwaitstop Unused. .TP .BI Tkill " pid\fR[4]\fP note\fR[5]\fP" Kill process .I pid with the given textual .IR note . Unimplemented. .TP .BI Rkill Reply to successful .BR Tkill . Unused. .PP .SH SOURCE .B /os/port/devdbg.c .br .B /os/*/*break.c .br .B /os/*/trap.c .SH SEE ALSO .IR acid (10.1) .SH BUGS The protocol is not itself error-detecting let alone error-correcting, although that normally does not matter for debugging even over a serial line, provided the connection is reasonably sound.